Fluoroplastic AgglomerateET 6210AZ塑料是东莞市双帮塑胶原料有限公司常年销售的塑料，因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告，COA原料出厂报告,UL黄卡,ROSH报告,reach报告,SVHC报告,提供原料注塑加工工程中可能出现的各种异常现象解决方法，塑料牌号太多，本网站没有提供的本公司也有代理，详情请咨询本公司相关业务人员0769-87795123

 

13549213581

Technical Data

 

Features and Benefits

 

•Wide service temperature range

 

–200° to +150°C

 

•Low flammability

 

•Excellent electrical and

 

mechanical properties

 

•Very good resistance to solvents

 

and chemicals

 

•High resistance to outdoor

 

 

 

 

 

3M™ Dyneon™

Fluoroplastic Agglomerate

ET 6210AZ

 

Typical Properties

 

Property Test Method

Melt Flow Index (297°C/5 kg) ASTM D1238 9 g/10 min

Specific Gravity ASTM D792 1.73 g/cm3

Dielectric Constant ASTM D150 2.58 @ 1 MHz

Dielectric Strength, 0.1 mm ASTM D149 140 kV/mm

Melting Point ASTM D4591 267°C (513°F)

Maximum Service Temperature DIN 57207 part 6 150°C (302°F)

Limiting Oxygen Index (LOI) ASTM D2863 >30

 

 

weathering

 

•High light transmission in the

 

visible and UV ranges

 

•Non-stick characteristics

 

•Excellent tear resistance

 

•Low permeability

 

•Good resistance to radiation

 

 

Note: Data in this document are not for specification purposes.

 

 

Product Description

 

3M™ Dyneon™ Fluoroplastic Agglomerate ET 6210AZ is a melt processable fluoroplastic consisting mainly of alternating tetrafluoroethylene and ethylene monomer

 

units (ETFE). This partially crystalline fluorothermoplastic offers a valuable combination of properties. This agglomerate form can also be used for compounding.

 

Storage and Material Handling

 

ET 6210AZ has a shelf life of three years from date of manufacture provided it is stored in a clean, dry place in the original unopened container received from 3M.

 

ET 6210AZ is hydrophobic, and generally does not require drying before processing unless high humidity conditions create surface moisture adsorption.

 

 

Safety/Toxicology

 

This is a fluoroplastic material, so normal precautions observed with fluoroplastics should be followed. Before processing this product, be sure to read and follow all precautions and directions for use contained in the product label and the Material Safety Data Sheet. General handling/processing precautions include: (1) Process only in well-ventilated areas; (2) Do not smoke in areas contaminated with powder/residue from this product;

 

(3) Avoid eye contact; (4) After handling this product, wash any contacted skin with soap and water. Potential hazards, including evolution of vapors, can exist if processing occurs under excessively high temperature conditions. Vapor extractor units should be installed above processing equipment. When cleaning processing equipment, do not burn off any of this product with an open flame or in a furnace.

 

 

 

 

东莞市双帮塑胶原料有限公司大量销售塑料美国3M  ETFE 3M™ Dyneon™Fluoroplastic AgglomerateET 6210AZ因为塑料价格行情每天都有新的变化前天的报价不等于今天的报价。如果需要新的价格请电：13549213581，肖生。